OBD-II trouble code
U041D: Invalid Data Received From Rocker Arm Control Module 'B'
A module is receiving messages from rocker arm control module 'B', but the data inside them is implausible or out of range. The connection is alive — the content is wrong. This is the 'B' counterpart to U041C.
Quick facts
- System
- Network
- Category
- Network Communication
- Severity
- Medium severity
- Drivable
- Usually safe to drive short-term
- Repair cost range
- $100 – $900
- DIY difficulty
- Shop recommended
What does U041D mean?
Some engines use switching or variable rocker arms to change how the valves open — the mechanism behind variable valve lift and cylinder deactivation (systems marketed as VTEC, VVL, AFM/DFM, MultiAir, and similar). A rocker arm control module operates the oil-control solenoids and switching pins that lock and unlock those rocker arms and reports state and feedback to the engine control module over the network. The 'B' designation identifies the second such module or bank — the counterpart to rocker arm control module 'A' (code U041C). U041D sets when a receiving module is still hearing from rocker arm control module 'B', but the data in its messages is invalid: a value is out of range, implausible, or contradicts what other modules see. The link is alive; the content can't be trusted — which is the key difference from a lost-communication code, where the module has gone silent.
Because the fault is bad data rather than a dead bus, the causes cluster around whatever makes the module broadcast wrong information. A failing input — an oil pressure or rocker-arm position/feedback sensor, or a switching solenoid reporting an implausible state — can push the module into sending values other modules reject. Low system voltage is a classic trigger, and because these switching mechanisms depend on oil pressure, low or dirty engine oil can produce genuine feedback the module then reports as out of range. The module's own software can be at fault if it is outdated, corrupted, or was never properly programmed after a replacement. Corroded connectors and chafed wiring around the valve cover complete the common list.
Symptoms depend on which data is invalid. You may see a check engine light, a loss of the high-lift power band on the affected bank, a cylinder-deactivation function that stops working (lowering fuel economy), or occasional rough running during a mode transition. On a V-configuration engine, U041D specifically points at the 'B' bank, so it can help localize which side of the engine to inspect. The vehicle usually remains driveable in a safe default valve mode, but performance and efficiency suffer. U041D is frequently a secondary code — read the full list, because a companion valvetrain, oil-pressure, or VVT code often names the real root cause. Address a low or dirty oil condition first; it is a cheap and common contributor.
Common causes
- Failing oil pressure or rocker-arm position/feedback sensor feeding the module bad data
- Low or dirty engine oil affecting the switching mechanism and its feedback
- Faulty oil-control solenoid reporting an implausible switching state
- Low system voltage or a weak battery/charging system
- Outdated, corrupted, or mismatched rocker arm control module software
- Module replaced without proper programming
- Corroded connectors or chafed wiring around the valve cover
- Rocker arm control module internal fault
Symptoms
- Check engine light illuminated
- Loss of the high-lift power band on the affected bank
- Cylinder deactivation stops working, lowering fuel economy
- Occasional rough running or hesitation during a valve-mode transition
- Companion valvetrain, oil-pressure, or VVT codes stored alongside U041D
- Vehicle generally still driveable in a default valve mode
Diagnostic steps
- 1.Read ALL stored codes first — U041D is often secondary to an oil-pressure, VVT, or valvetrain code that names the real fault.
- 2.Check engine oil level and condition; low or dirty oil is a common contributor to switching-rocker feedback faults.
- 3.Check battery and charging system voltage; low voltage is a common cause of implausible module data.
- 4.Use live data to compare the module's reported switching state and oil pressure against expected values, focusing on the 'B' bank.
- 5.Inspect connectors and wiring at the valve cover and module for corrosion and chafing.
- 6.Verify the module has the correct, current calibration, especially after a recent replacement or flash.
- 7.Address any companion codes before condemning the module itself; the underlying fault often clears U041D.
Repair cost
$100 – $900
Cost depends on what is producing the bad data. An oil change to restore proper oil condition is $50-$120 and sometimes the whole fix. An oil-control solenoid or oil pressure sensor typically runs $150-$450 installed. Correcting low voltage is $150-$600. A module reflash is usually $100-$300, and module replacement with programming is the expensive case — but that should only follow thorough diagnosis, since U041D is frequently a secondary code.
Estimate your repair
Run the numbers for your vehicle
Open the Repair Cost Estimator with module communication / can bus diagnosis preselected. Adjust labor rate and vehicle category to fit your situation.
DIY vs shop
Leave this one to a qualified shop. It typically involves emissions-critical components, refrigerant handling, or other work that requires manufacturer-grade tooling, training, or certification. DIY attempts often produce a more expensive problem than the original code.